2001 Dodge/Ram 3500 Regular Cab 4X2 & 4X4 Gas or Diesel 8'

Towing
Towing / SuperHitch Outlaw Towing Series.

Your Hitch:

Factory OEM Hitch
Upgrade Available*
SuperHitch Original 20K - D1100

Make This Your Hitch

*Caution: Your rear tie downs will change with your hitch application.
Front Hitch

There are no fits available.Please use our contact form and let us know!

Tie Downs and Turnbuckles

*Actual Tie Downs will vary
Front Tie Downs

Front Steel Tie Downs - Cab Length Running Boards - D2100
MFG Part Number: D2100
Holes to drill: 2
Footnotes:
  1. Drilling may be required for Installation.
Rear Tie Downs (FOR Factory OEM Hitch)

Rear Steel Tie Downs - Factory Hitch - D3101
MFG Part Number: D3101
Holes to drill: 0
Footnotes:
  1. Requires a Factory installed hitch receiver with an open ended cross tube.
Turnbuckles

Now that you know what Tie downs will fit your truck and camper, you can choose from our popular Springloading Turnbuckles. (You must select from one of our Springloaded Turnbuckles to maintain your Torklift camper anchor warranty.)



Basic Springload - S9000
Learn More


SpringLoad XL - S9050A
Learn More


Original FastGuns
Learn More
Tie Down and FastGun Locks

Tie Down Locks - S9700
MFG Part Number: S9700
Holes to drill: 0

FastGun Locks - S9500
MFG Part Number: S9500
Holes to drill: 0
Suspension
StableLoad - Suspension Stabilizer

StableLoad - A7200
MFG Part Number: A7200
Holes to drill: 0
Footnotes:
  1. The A7200/A7202 is a NO DRILL APPLICATION and must have a factory installed upper overload.
    -Will not work in conjunction with SuperSprings.
    -Due to factory overload engagement design, some applications have progressive engagement, where rear springs will contact first.
    -Drilling of rubber pad on some older Dodge applications may be required. Depending on the vehicle model, suspension package and condition, actual distance between the StableLoad and vehicle frame overload contact bracket may vary. In some rare instances, when the vehicle is not carrying a load, the StableLoad may come into contact due to rough road conditions and other anomalies. -(A7201 Spacer kit) is available for vehicles that need additional spacing for the StableLoad to contact the overload spring.

StableLoad - A7311
MFG Part Number: A7311
Holes to drill: 4
Footnotes:
  1. All lower leaf spring mounted StableLoads (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
    -Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
    -Average drill time is 30-40 minutes for complete installation
    -Many factory overload springs come pre-drilled with 1/2
  2. All lower leaf spring mounted StableLoads: Due to truck manufacture design, wear and tear and after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement and disengagement when the vehicle is unloaded. Must be conventional steel leaf springs. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8. To engage or. dis-engage weight may need to be take off springs if multiple wedges are used.

StableLoad - A7311S
MFG Part Number: A7311S
Holes to drill: 4
Footnotes:
  1. All lower leaf spring mounted StableLoads (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
    -Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
    -Average drill time is 30-40 minutes for complete installation
    -Many factory overload springs come pre-drilled with 1/2
  2. All lower leaf spring mounted StableLoads: Due to truck manufacture design, wear and tear and after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement and disengagement when the vehicle is unloaded. Must be conventional steel leaf springs. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8. To engage or. dis-engage weight may need to be take off springs if multiple wedges are used.
Auxiliary Battery Storage
HiddenPower

There are no fits available.Please use our contact form and let us know!